Unitor HPC Extreme 520 Specifications Page 124
- Page / 211
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
50
Technical data
Fuel system
Injection sequence
TD420VE/TAD420VE/TD520GE/
TAD530/531GE/TAD520VE,TAD532GE: ................ 1-3-4-2
TAD620VE/TD720GE/TAD730/731GE/
TAD720VE/TAD732GE/TAD721VE/TAD733GE
TAD722VE: ............................................................. 1-5-3-6-2-4
Feed pump
Supply pressure: ........................................................ 0.5 MPa (72.5 psi)
Supply pressure after fuel filter at
1500 rpm: Min ......................................................... 0.28 MPa (40.6 psi)
By-pass valve
Opening pressure ....................................................... 360–440 kPa (52.2–63.8 psi)
Fuel specification
The fuel must comply with national and international standards for commercially supplied fuels, such as:
EN 590 (with nationally adapted environmental and cold requirements)
ASTM D 975 No 1-D and 2-D.
JIS KK 2204
Sulfur content: Complying with legal requirements in each country.
Low density fuel (urban diesel in Sweden and city diesel in Finland) can cause a loss of up to 5% of power and an
increase in fuel consumption of about 2-3%.
122/209
- User and maintenance manual 1
- WARNING 2
- 1. Preface 5
- 1.1. General recommendations 5
- 1.3.1 General advice 10
- 1.4. Identifying sets 14
- 2. General description 16
- 2.1. Description 16
- 2.3. Fuel and consumables 21
- 2.3.1 Specifications 21
- 2.3.1.1. Oil grades 21
- 3. Installation 23
- 3.1. Unloading 23
- 3.1.2.1. Slings 23
- 3.1.2.2. Fork lift truck 24
- 3.2. Fluid retention 24
- 3.3. Choice of location 26
- 3.4. Electricity 27
- 3.5. Special arrangements 29
- 4. Trailer 29
- 4.1. Trailer linkage 29
- 4.2. Check before towing 29
- 4.3. Operation 30
- 4.4. Unhitching the trailer 30
- 4.7. Faults and repairs 33
- 5.1. Installation checks 35
- 6. Using the generator set 35
- 6.1. Pre-Start Inspection 35
- 6.2.2 Manual starting 40
- 6.2.3 Switching off 41
- 6.2.4 Alarms and faults 41
- 6.3.2 Starting 57
- Open the circuit breaker 58
- Press the STOP button 58
- Alarms 59
- Faults 59
- 6.3.4.5. Horn reset 63
- 7. Maintenance schedule 64
- 7.1. Reminder of use 64
- 7.2. Engine 64
- 7.3. Alternator 64
- 8. Battery 65
- 8.1. Storage and transport 65
- 8.3. Check 66
- 8.4. Load preconization 67
- 8.5. Faults and remedies 68
- 9. Appendix 69
- 33522077701_0_1 71
- OPERATOR’S MANUALp 73
- Foreword 74
- Table of contents 75
- Safety information 76
- Fire and explosion 78
- Hot surfaces and fluids 78
- Chemicals 78
- Electric welding 79
- Introduction 80
- Certified engines 81
- Warranty 81
- Presentation 82
- Identification numbers 84
- Instruments 86
- Starting the engine 87
- Starting in extreme cold 88
- Never use start spray 89
- Stopping the engine 91
- Maintenance schedule 92
- Maintenance 94
- Engine Oilgrade 96
- Oil level. Inspection 97
- Viscosity 97
- Oil change volume 97
- Oil and oil filters. Change 98
- Coolant. Mixture 100
- Water quality 100
- Coolant. Checking and filling 101
- Coolant. Draining 102
- Drain/vent taps. Location 102
- Cooling system Flushing 103
- External cleaning 103
- Fuel system 104
- Fuel system. Venting 105
- Fuel filter. Change 105
- Electrical system 106
- Battery. Maintenance 107
- Batteries, charging 108
- Component location 109
- Laying up 110
- Fault tracing 111
- Diagnostic function 112
- Operation 113
- Fault codes 114
- Technical data 120
- Including clutch and frame 121
- Lubrication system 123
- Fuel specification 124
- Cooling system 125
- Yes please 129
- Oui merci 129
- Sì, grazie 130
- Sí gracias 130
- Ja tack 130
- Ja graag 131
- Kyllä kiitos 131
- Sim, obrigado(a)! 131
- Îòïðàâüòå ýòîò òàëîí 132
- 7745131 English 06-2007 134
- 01/03/2012 137
- 33522061001_8_1 137
- LSA 46.2 - 4 POLES 139
- 2011.01/ h 140
- 3856 en 140
- 338 567 258 RCS ANGOULÊME 162
- 4067 en - 2009.05 / b 163
- 4067 en - 2009.05 / b 164
- (U/F only) 169
- 3 - INSTALLATION 170
- COMMISSIONING 170
- 3.2 - Settings 170
- Installation and maintenance 175
- 2012.03 / e 176
- 4531 en 176
- 1 - GENERAL INFORMATION 178
- 1.1 - Description 178
- 1.2 - Characteristic 178
- 2 - POWER SUPPLY 179
- 2.1 - AREP excitation system 179
- 2.2 - PMG excitation system 180
- R 450 181
- Diagram 1 183
- I exc(A) 183
- Diagram 2 184
- 1 PHASE SENSING 185
- 3 PHASES SENSING 185
- 3.3 - U/F and LAM function 186
- LAM (U/F only) 186
- 3.5 - AVR options 187
- 4.2 - Setting up 188
- Field forcing 190
- Rental Power 195
- GENCOOL 196
- 196
- ALTERNATOR 196
© 2020, manymanuals.com. All rights reserved. | 1.960 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals