Unitor HPC Extreme 520 Specifications Page 41
- Page / 211
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6.2.3 Switching off
Trigger the circuit breaker located at the base of the centre console.
Let the motor run under no load for 1 to 2 minutes to allow it to cool.
Press the "STOP" button to stop the generating set.
Switch off the MICS Nexys module by switching the key to "OFF" (without forcing it).
6.2.4 Alarms and faults
The appearance of a fault or an alarm causes the following
screen to be displayed (one or more pictograms or a fault code
along with the SOS message are displayed).
The user can access the following screens by pressing the key
The fault or alarm screen will disappear once the fault or alarm has been removed.
Only one fault is displayed on this screen (the fault which caused the generating set to stop).
If one or more faults have appeared after the first fault, they can only be displayed after the first fault has been reset (press
"Reset" as many times as the number of faults present).
Note : an alarm can appear at the same time as a fault.
39/209
- User and maintenance manual 1
- WARNING 2
- 1. Preface 5
- 1.1. General recommendations 5
- 1.3.1 General advice 10
- 1.4. Identifying sets 14
- 2. General description 16
- 2.1. Description 16
- 2.3. Fuel and consumables 21
- 2.3.1 Specifications 21
- 2.3.1.1. Oil grades 21
- 3. Installation 23
- 3.1. Unloading 23
- 3.1.2.1. Slings 23
- 3.1.2.2. Fork lift truck 24
- 3.2. Fluid retention 24
- 3.3. Choice of location 26
- 3.4. Electricity 27
- 3.5. Special arrangements 29
- 4. Trailer 29
- 4.1. Trailer linkage 29
- 4.2. Check before towing 29
- 4.3. Operation 30
- 4.4. Unhitching the trailer 30
- 4.7. Faults and repairs 33
- 5.1. Installation checks 35
- 6. Using the generator set 35
- 6.1. Pre-Start Inspection 35
- 6.2.2 Manual starting 40
- 6.2.3 Switching off 41
- 6.2.4 Alarms and faults 41
- 6.3.2 Starting 57
- Open the circuit breaker 58
- Press the STOP button 58
- Alarms 59
- Faults 59
- 6.3.4.5. Horn reset 63
- 7. Maintenance schedule 64
- 7.1. Reminder of use 64
- 7.2. Engine 64
- 7.3. Alternator 64
- 8. Battery 65
- 8.1. Storage and transport 65
- 8.3. Check 66
- 8.4. Load preconization 67
- 8.5. Faults and remedies 68
- 9. Appendix 69
- 33522077701_0_1 71
- OPERATOR’S MANUALp 73
- Foreword 74
- Table of contents 75
- Safety information 76
- Fire and explosion 78
- Hot surfaces and fluids 78
- Chemicals 78
- Electric welding 79
- Introduction 80
- Certified engines 81
- Warranty 81
- Presentation 82
- Identification numbers 84
- Instruments 86
- Starting the engine 87
- Starting in extreme cold 88
- Never use start spray 89
- Stopping the engine 91
- Maintenance schedule 92
- Maintenance 94
- Engine Oilgrade 96
- Oil level. Inspection 97
- Viscosity 97
- Oil change volume 97
- Oil and oil filters. Change 98
- Coolant. Mixture 100
- Water quality 100
- Coolant. Checking and filling 101
- Coolant. Draining 102
- Drain/vent taps. Location 102
- Cooling system Flushing 103
- External cleaning 103
- Fuel system 104
- Fuel system. Venting 105
- Fuel filter. Change 105
- Electrical system 106
- Battery. Maintenance 107
- Batteries, charging 108
- Component location 109
- Laying up 110
- Fault tracing 111
- Diagnostic function 112
- Operation 113
- Fault codes 114
- Technical data 120
- Including clutch and frame 121
- Lubrication system 123
- Fuel specification 124
- Cooling system 125
- Yes please 129
- Oui merci 129
- Sì, grazie 130
- Sí gracias 130
- Ja tack 130
- Ja graag 131
- Kyllä kiitos 131
- Sim, obrigado(a)! 131
- Îòïðàâüòå ýòîò òàëîí 132
- 7745131 English 06-2007 134
- 01/03/2012 137
- 33522061001_8_1 137
- LSA 46.2 - 4 POLES 139
- 2011.01/ h 140
- 3856 en 140
- 338 567 258 RCS ANGOULÊME 162
- 4067 en - 2009.05 / b 163
- 4067 en - 2009.05 / b 164
- (U/F only) 169
- 3 - INSTALLATION 170
- COMMISSIONING 170
- 3.2 - Settings 170
- Installation and maintenance 175
- 2012.03 / e 176
- 4531 en 176
- 1 - GENERAL INFORMATION 178
- 1.1 - Description 178
- 1.2 - Characteristic 178
- 2 - POWER SUPPLY 179
- 2.1 - AREP excitation system 179
- 2.2 - PMG excitation system 180
- R 450 181
- Diagram 1 183
- I exc(A) 183
- Diagram 2 184
- 1 PHASE SENSING 185
- 3 PHASES SENSING 185
- 3.3 - U/F and LAM function 186
- LAM (U/F only) 186
- 3.5 - AVR options 187
- 4.2 - Setting up 188
- Field forcing 190
- Rental Power 195
- GENCOOL 196
- 196
- ALTERNATOR 196
© 2020, manymanuals.com. All rights reserved. | 2.345 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals